Top 23 for Best Corner Radius End Mill

 

Niagara Cutter N47773 Carbide Corner Radius End Mill Uncoated Bright Finish RoughingFinishing Cut 35-Degree 3-Flute 51 mm OAL 6 mm Cut Diameter 6000 mm Shank Diameter 05 Radius

Niagara Cutter N47773 Carbide Corner Radius End Mill, Uncoated Bright Finish, Roughing/Finishing Cut, 35-Degree, 3-Flute, 51 mm OAL, 6 mm Cut Diameter, 6.000 mm Shank Diameter, 0.5″ Radius

Niagara Cutter N47773 Carbide Corner Radius End Mill, Uncoated Bright Finish, Roughing/Finishing Cut, 35-Degree, 3-Flute, 51 mm OAL, 6 mm Cut Diameter, 6.000 mm Shank Diameter, 0.5″ Radius - Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. 35-degree helix angle provides increased cutting action and chip evacuation compared to lower helix angles for machining stainless steel and titanium. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications. Corner radius end mills have cutting edges with rounded corners to reduce chipping and provide longer tool life. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling.

 

Niagara Cutter N68646 Carbide Corner Radius End Mill Inch AlCrN Finish Roughing and Finishing Cut 5 Flutes 25 Overall Length 0250 Cutting Diameter 0250 Shank Diameter 0045 Corner Radius

Niagara Cutter N68646 Carbide Corner Radius End Mill, Inch, AlCrN Finish, Roughing and Finishing Cut, 5 Flutes, 2.5″ Overall Length, 0.250″ Cutting Diameter, 0.250″ Shank Diameter, 0.045″ Corner Radius

Niagara Cutter N68646 Carbide Corner Radius End Mill, Inch, AlCrN Finish, Roughing and Finishing Cut, 5 Flutes, 2.5″ Overall Length, 0.250″ Cutting Diameter, 0.250″ Shank Diameter, 0.045″ Corner Radius - Aluminum chromium nitride (alcrn) coating provides good hardness and better resistance to chemical breakdown in high-heat applications than tialn, ticn, and tin coatings. Five flutes produce a better finish than fewer flutes and allow for higher feed rates compared to the four-flute stabilizer, depending on the type of material being milled and the cutting depth. Corner radius end mills have cutting edges with rounded corners to reduce chipping and provide longer tool life. Stabilizer flute design uses unequal spacing and variable helix angles to minimize tool vibration and remove up to three times more chips per minute than conventional carbide end mills. The combination of stabilizer flute geometry, carbide substrate, and alcrn coating make this end mill suitable for use on hard materials such as steels, stainless steels, and high-temperature alloys.

 

Kodiak Cutting Tools KCT152304 USA Made Solid Carbide 006 Corner Radius End Mill with 12 Shank Diameter 4 Flute 1 Length of Cut 3 Overall Length

Kodiak Cutting Tools KCT152304 USA Made Solid Carbide 0.06″ Corner Radius End Mill with 1/2″ Shank Diameter, 4 Flute, 1″ Length of Cut, 3″ Overall Length

Kodiak Cutting Tools KCT152304 USA Made Solid Carbide 0.06″ Corner Radius End Mill with 1/2″ Shank Diameter, 4 Flute, 1″ Length of Cut, 3″ Overall Length - 1/2 inch diameter solid carbide end mill, with radius 1/2″ shank 1″ length of cut 3″ overall length 4 flute radius-. 060 carbide, corner radius.

 

Kodiak Cutting Tools KCT154603 USA Made Solid Carbide 003 Corner Radius End Mill with 14 Shank Diameter 4 Flute 1-12 Length of Cut 4 Overall Length

Kodiak Cutting Tools KCT154603 USA Made Solid Carbide 0.03″ Corner Radius End Mill with 1/4″ Shank Diameter, 4 Flute, 1-1/2″ Length of Cut, 4″ Overall Length

Kodiak Cutting Tools KCT154603 USA Made Solid Carbide 0.03″ Corner Radius End Mill with 1/4″ Shank Diameter, 4 Flute, 1-1/2″ Length of Cut, 4″ Overall Length - . 030 carbide, corner radius. 1/4 inch diameter solid carbide end mill, with radius 1/4″ shank 1-1/2″ length of cut 4″ overall length 4 flute radius-0.

 

Niagara Cutter N18600-010 Carbide Corner Radius End Mill Long LengthReach TiCN Finish RoughingFinishing 45-Degree 3-Flute 4 OAL 0375 Cut Diameter 0375 Shank Diameter 001 Radius

Niagara Cutter N18600-010 Carbide Corner Radius End Mill, Long Length/Reach, TiCN Finish, Roughing/Finishing, 45-Degree, 3-Flute, 4″ OAL, 0.375″ Cut Diameter, 0.375″ Shank Diameter, 0.01″ Radius

Niagara Cutter N18600-010 Carbide Corner Radius End Mill, Long Length/Reach, TiCN Finish, Roughing/Finishing, 45-Degree, 3-Flute, 4″ OAL, 0.375″ Cut Diameter, 0.375″ Shank Diameter, 0.01″ Radius - Corner radius end mills with extended-reach neck style have cutting edges with rounded corners to reduce chipping and provide longer tool life, and a longer neck to provide access to recessed areas of the workpiece. 45-degree helix provides the efficient cutting action and chip evacuation required to machine aluminum and other nonferrous materials. Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers better abrasion resistance than uncoated tools. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications. Wiper flat on cutting edges for a smoother finish than conventional end mills.

 

Kodiak Cutting Tools KCT154779 USA Made Solid Carbide Corner Radius End Mill with 38 Shank 4 Flute 0045 4 Overall Length 1-34 Length of Cut

Kodiak Cutting Tools KCT154779 USA Made Solid Carbide Corner Radius End Mill with 3/8″ Shank, 4 Flute, 0.045″, 4″ Overall Length, 1-3/4″ Length of Cut

Kodiak Cutting Tools KCT154779 USA Made Solid Carbide Corner Radius End Mill with 3/8″ Shank, 4 Flute, 0.045″, 4″ Overall Length, 1-3/4″ Length of Cut - . 3/8 inch diameter solid carbide end mill, with radius 3/8″ shank 1-3/4″ length of cut 4″ overall length 4 flute radius-0. 045 carbide, corner radius.

 

Niagara Cutter N61813 Carbide Corner Radius End Mill TiAlN Finish Finishing Cut 35 Degree Helix 3 Flutes 25 Overall Length 0281 Cut Diameter 03125 Shank Diameter 0020 Corner Radius

Niagara Cutter N61813 Carbide Corner Radius End Mill, TiAlN Finish, Finishing Cut, 35 Degree Helix, 3 Flutes, 2.5″ Overall Length, 0.281″ Cut Diameter, 0.3125″ Shank Diameter, 0.020″ Corner Radius

Niagara Cutter N61813 Carbide Corner Radius End Mill, TiAlN Finish, Finishing Cut, 35 Degree Helix, 3 Flutes, 2.5″ Overall Length, 0.281″ Cut Diameter, 0.3125″ Shank Diameter, 0.020″ Corner Radius - Corner radius end mills have cutting edges with rounded corners to reduce chipping and provide longer tool life. Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than tin and ticn coatings. Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications. 35-degree helix angle provides increased cutting action and chip evacuation compared to lower helix angles for machining stainless steel and titanium.

 

Kodiak Cutting Tools KCT152095 USA Made Solid Carbide 0015 Corner Radius End Mill with 14 Shank Diameter 4 Flute 34 Length of Cut 2-12 Overall Length

Kodiak Cutting Tools KCT152095 USA Made Solid Carbide 0.015″ Corner Radius End Mill with 1/4″ Shank Diameter, 4 Flute, 3/4″ Length of Cut, 2-1/2″ Overall Length

Kodiak Cutting Tools KCT152095 USA Made Solid Carbide 0.015″ Corner Radius End Mill with 1/4″ Shank Diameter, 4 Flute, 3/4″ Length of Cut, 2-1/2″ Overall Length - 015 carbide, corner radius. 1/4 inch diameter solid carbide end mill, with radius 1/4″ shank 3/4″ length of cut 2-1/2″ overall length 4 flute radius-.

 

Melin Tool VXMG Carbide Corner Radius End Mill Variable Helix nACo Monolayer Finish Roughing Cut Helix 4 Flutes 2 Overall Length 03750 Cutting Diameter 03750 Shank Diameter 003 Corner Radius

Melin Tool VXMG Carbide Corner Radius End Mill, Variable Helix, nACo Monolayer Finish, Roughing Cut, Helix, 4 Flutes, 2″ Overall Length, 0.3750″ Cutting Diameter, 0.3750″ Shank Diameter, 0.03″ Corner Radius

Melin Tool VXMG Carbide Corner Radius End Mill, Variable Helix, nACo Monolayer Finish, Roughing Cut, Helix, 4 Flutes, 2″ Overall Length, 0.3750″ Cutting Diameter, 0.3750″ Shank Diameter, 0.03″ Corner Radius - Enables higher spindle speed and heavier chip loads. Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems. Provides chatter-free machining. Round shanks allow use with a wide variety of toolholding systems. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications.

 

Cleveland C60568 Solid Carbide 5-Flute Corner Radius End Mill 05 Diameter Spiral Flute Straight Shank wo Flats Bright Uncoated Finish Pack qty 1

Cleveland C60568 Solid Carbide 5-Flute Corner Radius End Mill, 0.5″ Diameter, Spiral Flute, Straight Shank w/o Flats, Bright (Uncoated) Finish (Pack qty. 1)

Cleveland C60568 Solid Carbide 5-Flute Corner Radius End Mill, 0.5″ Diameter, Spiral Flute, Straight Shank w/o Flats, Bright (Uncoated) Finish (Pack qty. 1) - 0600 single end/double end single end number of flutes 5 length of cut 1-1/4 end mill cutting type center overall length 3 finish bright shank dia. Technical specification item corner radius end mill grade high performance list number cem-v2-5r end mill style corner radius end mill material carbide dimension type fractional inch milling dia. 1/2 cutting direction right hand helix angle 38 degrees end mill application roughing/finishing steel (p) compatibility yes stainless (m) compatibility yes cast iron (k) compatibility no non ferrous (n) compatibility no super alloy (s) compatibility yes hardened (h) compatibility yes this listing is for each. 1/2 corner radius 0. .

 

Kodiak Cutting Tools KCT151072 USA Made Solid Carbide 0045 Corner Radius End Mill with 14 Shank Diameter 2 Flute 34 Length of Cut 2-12 Overall Length

Kodiak Cutting Tools KCT151072 USA Made Solid Carbide 0.045″ Corner Radius End Mill with 1/4″ Shank Diameter, 2 Flute, 3/4″ Length of Cut, 2-1/2″ Overall Length

Kodiak Cutting Tools KCT151072 USA Made Solid Carbide 0.045″ Corner Radius End Mill with 1/4″ Shank Diameter, 2 Flute, 3/4″ Length of Cut, 2-1/2″ Overall Length - 045 carbide, corner radius. 1/4 inch diameter solid carbide end mill, with radius 1/4″ shank 3/4″ length of cut 2-1/2″ overall length 2 flute radius-.

 

Cobra Carbide 19416 Micro Grain Solid Carbide Regular Length General End Mill Uncoated Bright Finish 4 Flute 30 Degrees Helix 0030 Radius Corner End 12 Cutting Length 18 Cutting Diameter 1-12 Length Pack of 1

Cobra Carbide 19416 Micro Grain Solid Carbide Regular Length General End Mill, Uncoated (Bright) Finish, 4 Flute, 30 Degrees Helix, 0.030″ Radius Corner End, 1/2″ Cutting Length, 1/8″ Cutting Diameter, 1-1/2″ Length (Pack of 1)

Cobra Carbide 19416 Micro Grain Solid Carbide Regular Length General End Mill, Uncoated (Bright) Finish, 4 Flute, 30 Degrees Helix, 0.030″ Radius Corner End, 1/2″ Cutting Length, 1/8″ Cutting Diameter, 1-1/2″ Length (Pack of 1) - Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. Corner radius gives more strength. Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems. Round shanks allow use with a wide variety of toolholding systems. Used for roughing and finishing operation.

 

Niagara Cutter N85586-030 Carbide Corner Radius End Mill TiAlN Finish Roughing and Finishing Cutting 30-Degree Helix 4-Flute 15 OAL 0125 Cut Diameter 0125 Shank Diameter 0030 Radius

Niagara Cutter N85586-030 Carbide Corner Radius End Mill, TiAlN Finish, Roughing and Finishing Cutting, 30-Degree Helix, 4-Flute, 1.5″ OAL, 0.125″ Cut Diameter, 0.125″ Shank Diameter, 0.030″ Radius

Niagara Cutter N85586-030 Carbide Corner Radius End Mill, TiAlN Finish, Roughing and Finishing Cutting, 30-Degree Helix, 4-Flute, 1.5″ OAL, 0.125″ Cut Diameter, 0.125″ Shank Diameter, 0.030″ Radius - Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures. Corner radius end mills have cutting edges with rounded corners to reduce chipping and provide longer tool life. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than tin and ticn coatings. Four flutes produce a better finish than fewer flutes.

 

Niagara Cutter N18655 Carbide Corner Radius End Mill Long LengthReach AlTiN Finish RoughingFinishing Cut 35-Degree 3-Flute 5 OAL 0500 Cut Diameter 0500 Shank Diameter 003 Radius

Niagara Cutter N18655 Carbide Corner Radius End Mill, Long Length/Reach, AlTiN Finish, Roughing/Finishing Cut, 35-Degree, 3-Flute, 5″ OAL, 0.500″ Cut Diameter, 0.500″ Shank Diameter, 0.03″ Radius

Niagara Cutter N18655 Carbide Corner Radius End Mill, Long Length/Reach, AlTiN Finish, Roughing/Finishing Cut, 35-Degree, 3-Flute, 5″ OAL, 0.500″ Cut Diameter, 0.500″ Shank Diameter, 0.03″ Radius - 35-degree helix angle provides increased cutting action and chip evacuation compared to lower helix angles for machining stainless steel and titanium. Extended-reach neck style provides access to recessed areas of the workpiece. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications. Corner radius end mills have cutting edges with rounded corners to reduce chipping and provide longer tool life. Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than tin and ticn coatings.

 

YG-1 EM637 Carbide Corner Radius End Mill Uncoated Bright Finish 30 Deg Helix 2 Flutes 3 Overall Length 0375 Cutting Diameter 0375 Shank Diameter 0020 Corner Radius

YG-1 EM637 Carbide Corner Radius End Mill, Uncoated (Bright) Finish, 30 Deg Helix, 2 Flutes, 3″ Overall Length, 0.375″ Cutting Diameter, 0.375″ Shank Diameter, 0.020″ Corner Radius

YG-1 EM637 Carbide Corner Radius End Mill, Uncoated (Bright) Finish, 30 Deg Helix, 2 Flutes, 3″ Overall Length, 0.375″ Cutting Diameter, 0.375″ Shank Diameter, 0.020″ Corner Radius - Two flutes offer better chip-carrying capacity than end mills with more flutes, enhancing the tool’s ability to remove material. Suitable for high-performance machining on tool steel, alloy steel, mold steel, and other high-hardened materials up to rockwell hardness c70. Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than tin and ticn coatings. High-performance carbide provides better wear resistance and toughness than standard carbide and can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Corner radius end mills have cutting edges with rounded corners to reduce chipping and provide longer tool life.

 

Kodiak Cutting Tools KCT153503 USA Made Solid Carbide 0015 Corner Radius End Mill with 12 Shank Diameter 4 Flute 2 Length of Cut 4 Overall Length

Kodiak Cutting Tools KCT153503 USA Made Solid Carbide 0.015″ Corner Radius End Mill with 1/2″ Shank Diameter, 4 Flute, 2″ Length of Cut, 4″ Overall Length

Kodiak Cutting Tools KCT153503 USA Made Solid Carbide 0.015″ Corner Radius End Mill with 1/2″ Shank Diameter, 4 Flute, 2″ Length of Cut, 4″ Overall Length - 015 carbide, corner radius. . 1/2 inch diameter solid carbide end mill, with radius 1/2″ shank 2″ length of cut 4″ overall length 4 flute radius-0.

 

Niagara Cutter N57906 Carbide Corner Radius End Mill Long Reach Uncoated Bright Finish RoughingFinishing Cut 40-Degree 3-Flute 4 OAL 1000 Cut Diameter 1000 Shank Diameter 004 Radius

Niagara Cutter N57906 Carbide Corner Radius End Mill, Long Reach, Uncoated Bright Finish, Roughing/Finishing Cut, 40-Degree, 3-Flute, 4″ OAL, 1.000″ Cut Diameter, 1.000″ Shank Diameter, 0.04″ Radius

Niagara Cutter N57906 Carbide Corner Radius End Mill, Long Reach, Uncoated Bright Finish, Roughing/Finishing Cut, 40-Degree, 3-Flute, 4″ OAL, 1.000″ Cut Diameter, 1.000″ Shank Diameter, 0.04″ Radius - Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. 40-degree helix provides the efficient cutting action and chip evacuation required to machine aluminum and other nonferrous materials. Corner radius end mills with extended-reach neck style have cutting edges with rounded corners to reduce chipping and provide longer tool life, and a long neck to provide access to recessed areas of the workpiece. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications. Wiper flat on cutting edges for a smoother finish than conventional end mills.

 

Niagara Cutter N68639 Carbide Corner Radius End Mill Inch AlCrN Finish Roughing and Finishing Cut 5 Flutes 25 Overall Length 0250 Cutting Diameter 0250 Shank Diameter 0030 Corner Radius

Niagara Cutter N68639 Carbide Corner Radius End Mill, Inch, AlCrN Finish, Roughing and Finishing Cut, 5 Flutes, 2.5″ Overall Length, 0.250″ Cutting Diameter, 0.250″ Shank Diameter, 0.030″ Corner Radius

Niagara Cutter N68639 Carbide Corner Radius End Mill, Inch, AlCrN Finish, Roughing and Finishing Cut, 5 Flutes, 2.5″ Overall Length, 0.250″ Cutting Diameter, 0.250″ Shank Diameter, 0.030″ Corner Radius - Corner radius end mills have cutting edges with rounded corners to reduce chipping and provide longer tool life. Aluminum chromium nitride (alcrn) coating provides good hardness and better resistance to chemical breakdown in high-heat applications than tialn, ticn, and tin coatings. Stabilizer flute design uses unequal spacing and variable helix angles to minimize tool vibration and remove up to three times more chips per minute than conventional carbide end mills. The combination of stabilizer flute geometry, carbide substrate, and alcrn coating make this end mill suitable for use on hard materials such as steels, stainless steels, and high-temperature alloys. Five flutes produce a better finish than fewer flutes and allow for higher feed rates compared to the four-flute stabilizer, depending on the type of material being milled and the cutting depth.

 

Kodiak Cutting Tools KCT153228 USA Made Solid Carbide 003 Corner Radius End Mill with 14 Shank Diameter 4 Flute 1 Length of Cut 4 Overall Length

Kodiak Cutting Tools KCT153228 USA Made Solid Carbide 0.03″ Corner Radius End Mill with 1/4″ Shank Diameter, 4 Flute, 1″ Length of Cut, 4″ Overall Length

Kodiak Cutting Tools KCT153228 USA Made Solid Carbide 0.03″ Corner Radius End Mill with 1/4″ Shank Diameter, 4 Flute, 1″ Length of Cut, 4″ Overall Length - 030 carbide, corner radius. 1/4 inch diameter solid carbide end mill, with radius 1/4″ shank 1″ length of cut 4″ overall length 4 flute radius-0. .

 

Niagara Cutter N57914 Carbide Corner Radius End Mill Long Reach TiCN Finish RoughingFinishing Cut 40-Degree 3-Flute 325 OAL 0250 Cut Diameter 0250 Shank Diameter 001 Radius

Niagara Cutter N57914 Carbide Corner Radius End Mill, Long Reach, TiCN Finish, Roughing/Finishing Cut, 40-Degree, 3-Flute, 3.25″ OAL, 0.250″ Cut Diameter, 0.250″ Shank Diameter, 0.01″ Radius

Niagara Cutter N57914 Carbide Corner Radius End Mill, Long Reach, TiCN Finish, Roughing/Finishing Cut, 40-Degree, 3-Flute, 3.25″ OAL, 0.250″ Cut Diameter, 0.250″ Shank Diameter, 0.01″ Radius - Corner radius end mills with extended-reach neck style have cutting edges with rounded corners to reduce chipping and provide longer tool life, and a long neck to provide access to recessed areas of the workpiece. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications. Wiper flat on cutting edges for a smoother finish than conventional end mills. 40-degree helix provides the efficient cutting action and chip evacuation required to machine aluminum and other nonferrous materials. Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers better abrasion resistance than uncoated tools.

 

Bassett HPEM-3 Series Solid Carbide High-Performance End Mill TiCN Coated 3 Flute 30 Degrees Helix 0020 Radius Corner End 0375 Cutting Length 14 Cutting Diameter 2 Length Pack of 1

Bassett HPEM-3 Series Solid Carbide High-Performance End Mill, TiCN Coated, 3 Flute, 30 Degrees Helix, 0.020″ Radius Corner End, 0.375″ Cutting Length, 1/4″ Cutting Diameter, 2″ Length (Pack of 1)

Bassett HPEM-3 Series Solid Carbide High-Performance End Mill, TiCN Coated, 3 Flute, 30 Degrees Helix, 0.020″ Radius Corner End, 0.375″ Cutting Length, 1/4″ Cutting Diameter, 2″ Length (Pack of 1) - Titanium carbonitride coatings are harder and more wear-resistant than tin for improved tool life and faster cutting speeds. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Ideally suited for use in stainless steel and exotics such as hastalloy, waspalloy, and inconel. Weldon shanks feature a round shank with one of more flats machined into the side for easy indexing and alignment. Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems.

 

Melin Tool CCMG Carbide Corner Radius End Mill Uncoated Bright Finish 30 Deg Helix 4 Flutes 2 Overall Length 01875 Cutting Diameter 01875 Shank Diameter 0030 Corner Radius

Melin Tool CCMG Carbide Corner Radius End Mill, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 2″ Overall Length, 0.1875″ Cutting Diameter, 0.1875″ Shank Diameter, 0.030″ Corner Radius

Melin Tool CCMG Carbide Corner Radius End Mill, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 2″ Overall Length, 0.1875″ Cutting Diameter, 0.1875″ Shank Diameter, 0.030″ Corner Radius - Radius gives added strength to corner. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. Round shanks allow use with a wide variety of toolholding systems. Used when a radius is permissable. Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems.

 

YG-1 G8A37 Carbide Micro Corner Radius End Mill Metric Uncoated Bright Finish 30 Deg Helix 4 Flutes 40mm Overall Length 1mm Cutting Diameter 3mm Shank Diameter 01mm Corner Radius

YG-1 G8A37 Carbide Micro Corner Radius End Mill, Metric, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 40mm Overall Length, 1mm Cutting Diameter, 3mm Shank Diameter, 0.1mm Corner Radius

YG-1 G8A37 Carbide Micro Corner Radius End Mill, Metric, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 40mm Overall Length, 1mm Cutting Diameter, 3mm Shank Diameter, 0.1mm Corner Radius - Stub-length cutting edges and long-reach shank increase the strength of the tool while providing access to recessed areas of the workpiece. High-performance carbide provides better wear resistance and toughness than standard carbide and can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Corner radius end mills have cutting edges with rounded corners to reduce chipping and provide longer tool life. Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than tin and ticn coatings. Suitable for high-performance slotting and machining in recessed areas on hardened steel, heat-resistant steel, and materials with a rockwell hardness up to c70.





We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.